| 1. | The minimum thickness of the workpieces
零件的最小壁厚 |
| 2. | If you ship your fabric or wallpaper roll in a bag , please use a bag with a minimum thickness of 6 mm
如果您用袋子运输纺织品或墙纸卷，请使用厚度至少为六密耳的袋子 |
| 3. | If you ship your fabric or wallpaper roll in a bag , please use a bag with a minimum thickness of 6 mm
如果您使用胶袋来托运织物或墙纸，请使用厚度至少有六密尔单位的胶袋 |
| 4. | Am218 . 1 ( d ) , 原文 为 ： the governing thickness of a nonwelded dished head is the greater of the flat flange thickness divided by 4 or the minimum thickness of the dished portion
2004及以前版译为：非焊接碟形封头的控制厚度为较大的平法兰厚度除以4或碟形封头部分的最小厚度。 |
| 5. | The chinese codes stipulate both the width - thickness ratio and the minimum thickness of the elements . that is stricter than the stipulations of north american codes
对于受压板件的壁厚，我国规范采取的是既限制板件宽厚比又限制最小板厚的规定，其限制较北美同类规范偏严。 |
| 6. | Aerospace series . lubricating dry fluorocarbonated coating with binding material and fillers , of a minimum thickness of 5 micrometers on metallic substrate . quality of coated parts
航空航天系列.金属底层最小厚度5微米的带粘接材料和填料的干润滑碳氟化合物覆层.覆层零件质量 |
| 7. | The axial frictional pulling force and the minimum thickness of mucus film were analyzed and calculated in detail when rectangular or trapezoidal cylindrical screw was being adopted in microcomputer
详细分析计算了微型机器人在采用矩形和梯形圆柱螺旋时的轴向摩擦牵引力和最小粘液膜厚度。 |
| 8. | V - class thermistor film is successfully produced on silicon substrate and sio2 substrate applying cvd process for the first time in this paper , whose minimum thickness is only 600nm or so
本论文创沃性地采用十导体cvd工艺在硅中晶1底以及引；衬底1二if长出最小厚度为600urn的v系热敏电阻薄脏。 |
| 9. | Nominal thickness of insulatioh should be in accordance with the stipulations of table 1 , table2 . - 10 % discrepancy is allowed , but the minimum thickness should be not less than 90 % - 0 . 1 of nominal thickness
2绝缘绝缘标和厚度符合表1 、表2的规定，允许有- 10 %的偏差，其最薄厚度应不小于标称厚度的90 % - 0 . 1 |
| 10. | Wherethe long bridge deck within 0 . 5 l amidships is regarded as strengthdeck , the midship section modulus and minimum thickness of the deckplating comply with the requirements of 2 . 2 . 1 and 2 . 4 . 2 . l of this ischapter
例1 :在船中部0 . 5l区域内的长桥楼甲板作为强力甲板时，其船中剖面模数及最小厚度应满足本章2 . 2 . 1及2 . 4 . 2 . 1的要求。 |
